Effect of repair methods on mechanical behaviors of repair area in composite laminate fuselage skin with different damage size
DOI:
https://doi.org/10.18063/msacm.v0i0.797Keywords:
stress distribution, adhesive repair, adhesive-rivet hybrid repair, composite laminate fuselage skinAbstract
Composite laminates are widely used in the large civil aircrafts because of their excellent mechanical properties. The maintenance and repair of composite laminates become essential. In this paper, a new adhesive-rivet hybrid repair of composite laminate fuselage skin is presented. For the circular hole damage with the diameter of 90mm and 50mm, the finite element simulation models of adhesive repair and adhesive-rivet hybrid repair were built respectively. Uniform pressure load was applied on these finite element models. The mechanical properties of laminate motherboard, patch and adhesive film for these four models were analyzed. The effects of adhesive repair, adhesive-rivet hybrid repair on mechanical behaviors of repair areas of composite laminate fuselage skins with different damage size were studied. By analyzing the mechanical behaviors of these two repair methods, a suitable repair method can be obtained.References
Chawla KK. Composite material science and engineering. New York: Springer; 2001.
Fan YQ, Zhang LH. New development of extra composite aircraft components application technology. Acta Aeronautica et Astronautica Sinica 2009; 30(3): 534-543.
Erdogan F, Arin K. A sandwich plate with a pact-through and a debonding crack [J]. Engineering Fracture Mechanics 1972.
Cheng P, Gong XJ, Aivazzadeh S. Experimental observation of tensile behavior of patch repaired composites [J]. Polymer Testing 2014; 34: 146-154.
Zhao C, Nie HCg, Guo X, et al. Compression performance of composite stiffened panel after stiffener repair [J]. Journal of Beijing University of Aeronautics and Astronautics 2014; 06: 834-838.
Duong CN, Wang CH. Composite repair-theory and design [M]. Amsterdam: Elsevier 2007: 4-5.
Xie YA. Performance study of composite mechanically fastened joints and joint design [D]. Harbin Engineering University 2013.
Zhao MY. Failure analysis of composite mechanically fastened joints and study of effects on failure strength [D]. Northwestern Polytechnical University 2006.
Nie HC, Tan RM, Guo X, et al. Tensile performances of mechanically mastened repairs of composite laminates [J]. Journal of Beijing University of Aeronautics and Astronsutics 2015; 05: 1-10.
Kelly G. Load transfer in hybrid composite single-lap joints [J]. Composite Structures 2005; 69(1): 35-43.
Barut A, Madenci E. Analysis of bolted-bonded composite single lap joints under combined in-plane and transverse loading [J]. Composite Structures 2009; 88(4): 579-594.
Ding K, Dhanasekar M. Flexural behavior of bonded-bolted butt joints due to bolt looseness [J]. Advances in Engineering Software 2007; 38(8-9): 598-606.
Kweon JH, Jung JW. Failure of carbon composite-to-aluminum joints with combined mechanical fastening and adhesive bonding [J]. Composite Structures 2006; 75(1/2/3/4): 192-198.
Hart-Smith LJ. Bonded-bolted composite joints. Journal of Aircraft 1985; 22(11): 993-1000.
Zhang MX. Load distribution and finite element calculation of T800 Carbon Fiber Hyper Joints Composite Laminates [J]. Fiberglass/Composite 2011; (5): 62-66.
Chowdhury NM, Wang J, Chiu WK, et al. Experimental and Finite Element Studies of Thick Bolted, Bonded and Hybrid Carbon Fibre Step Lap Joints used in Aircraft Structures. Journal of Composites Part B. v100 2016; 68-77.
Yao L, Feng Q, Wan D, et al. Experiment and finite element simulation of high strength steel adhesive joint reinforced by rivet for automotive applications[J]. Journal of Adhesion Science & Technology 2016; 31(14): 1617-1625.
Gomez S, Onoro J, et al. A simple mechanical model of a structures hybrid adhesive/riveted single lap joint [J]. International Journal of Adhesion&Adhesives 2007; 27(4): 263-267.
Sadowski T, Zarzekaraczkowska E. Hybrid adhesive bonded and riveted joints - influence of rivet geometrical layout on strength of joints [J]. Archives of Metallurgy & Materials 2012; 57(4): 1127-1135.
Liu J, Zhang FP. Fatigue Life Prediction of Composite Laminate [J]. Advanced Materials Research 2012; 472-475: 591-595.
Meng M, Le HR, Rizvi MJ, et al. 3D FEA modelling of laminated composites in bending and their failure mechanisms [J]. Composite Structures 2015; 119: 693-708.
